SPH400, SPH426, Not Your Ordinary Laser Fume Extractor, Air Filtration System

Our most popular model Laser Fume Extractor for light and medium duty applications

The SPH400 series Laser Fume Extractor, Air Filtration System, is our most popular model for light and medium duty applications. It’s made here in North America, in Pointe-Claire, Quebec, Canada but has found its way to shops, labs, offices, workplaces around the world.

Here’s why.

4 stages, multi-stages of filtration

Capture-PF400-PF800

The Quatro Air SPH400 Fume Extractor and Air Filtration System is designed with up to 4 stages of filtration each targeted for removal of specific size particles and gases.

There are a series of filters in the system to ensure that all particulate matter/ dust is removed efficiently:

The unit contains multi-layer knock out pad filters, Deep Pleated high capacity safety filters and a MERV 17 99.97 % HEPA filter.

The HEPA filter is the last particulate filter in the sequence and it is designed to remove 99.97% of all particulate matter that is 0.3 microns and larger.

Same type of filter that is used in hospital operating rooms

This is the same type of filter that is used in hospital operating rooms. Please note as the filters begin to get dirty they also become more efficient making the system more efficient as time goes on. This occurs as it gets more and more difficult for the dust to pass through the filter due to the passages becoming smaller as they become filled with debris.

Odors, Fumes – gas phase filter is quite large and 8” deep

The gas phase filter is quite large and 8” deep in direction of airflow. We have 26 different types of chemical media that can be incorporated into the chemical filter to address and deal with specific contaminants if required.

Depending on the type of media the modules could weigh as much as 40 lbs.

Our standard and most typical module contains a virgin bituminous coal extruded 3-4 mm carbon pellet.

Ideal at removing many VOC’s

This carbon is ideal at removing many VOC’s and has a holding capacity as high as 25 % by weight. Initially the removal efficiency will be 100% for most VOC’s. Over time the mass transfer zone will travel through the chemical filter as it gets consumed.

A gel seal material to guarantee zero by-pass

The chemical filter is seated inside a gel seal material to guarantee zero by-pass of the chemical filter. This is the same material that is used in Pharmaceutical and Hospital environment clean rooms. All gases therefore must pass through the chemical filter

High pressure blowers to overcome the resistance created by the deep bed chemical filter

Unlike other systems that have a sprinkling of carbon our gas phase chemical filter is quite large and requires the use of high pressure blowers to overcome the resistance created by the deep bed chemical filter. Our blowers are capable of generating 90” water column of pressure. With this type of blower as the filters begin to get dirty and plugged we can still effectively overcome this increase in pressure. The system is equipped to advise you when the filters need to be changed.

For more information, visit our webpage at : http://www.airpurifiers-r-us.com/laser-fume-extractor.html or contact us using the contact form below.

Advertisements

Capturing and filtering chemical odors, gases

You will need an air filtration system with a source capture arm, a deep bed chemical odor filter, 8 inches, 15 inches or more in depth, possibly a HEPA filter (for removing smoke haze), a unit powered by a high speed, high pressure motor blower to overcome the static pressure of pulling contaminated air quickly from the source and through a mutli-stage filtration (that includes a deep bed chemical, odor, gas filter).

Our Fume Extractors can help you clean the air in your workshop.

For example, our CSA 600 series comes with these neat features:

 

  • Multi-stage filtration system: filter bag (or high capacity pleated filter), medical grade HEPA and chemical filter

    CSA-600 - Heavy Duty Dust & Odor Removal

    The CSA is the workhorse fume extractor of the laser industry; designed to operate in a heavy duty environment. A large pre-filter bag that is easily accessed to change via a convenient side panel eliminates much of the debris that might otherwise clog the more expensive HEPA filters. A huge chemical bed of 66Lb. (30kg) provides significant odor and VOC protection for much longer than the light duty units again providing a solution that can withstand a heavy workload. Chemical compounds can be customized based on specific applications With large collection bag, HEPA Filter & Deepbed Odor filters LaserBlue Gel seal guarantees NO BYPASS Dual hi-speed turbine for high suction, pressure & airflow Whisper quiet operation is office friendly Universal design allows for 2.5″, 3″, 4″ inlet along with discharge

  • Refillable, 15” deep chemical filter module, up to 66 lbs. (30kg)
  • LaserBlue gel seal guarantees ZERO FILTER BYPASS
  • Dual high speed turbine for high suction, pressure and airflow
  • Office friendly, whisper quiet operation
  • Digital control panel
  • Enhanced mobility with heavy duty lockable casters

Check out the specs on our CSA600 series fume extractor:

  • Air Flow: 0-480 m³/h / 0-282 CFM
  • Max Pressure: 90″ W.C. / 22 kPa
  • Motor(s): 2 X 1.0 kW High Speed Turbine
  • Voltage: 120V or 230V
  • Dimensions: 13″W x 21″D x 45″H / 330mm x 533mm x 1143mm
  • Filter Sequence: Antimicrobial high capacity bag filter (F128), 6″ Pleated filter, 60% ASHRAE rated (F073), 2” Medical grade HEPA Filter 99.97% (F074), 15“ Chemical filter (AG111)
  • Optional lnlets: 1.5”, 2”, 3” or 4″ diameter
  • Discharge: Recirculation grille (Standard configuration);
  • Optional 3″ or 4″ side discharge collars for venting to the exterior
  • Sound Level: 52 dBA at full speed
  • Controls: Remote ON/OFF, communication capabilities, audible and visual alarms
  • Suction hose: 6 feet (2m) of heavy duty hose and clamps

Visit our fume extractor web page at : http://www.airpurifiers-r-us.com/laser-fume-extractor.html.

For our other air filtration systems that could be of help to you with regards to chemical, odor, gas, control, filtration, purification, point your browser to http://www.airpurifiers-r-us.com/index.html

Feel free to reach to us by calling toll free, 1-800-626-0664, outside of North America, 1-514-364-5538, Skype: lito.espinosa, or use the contact form below.

 

Fume Extractor for small 3D printers

Meet our SPL400-3D fume extractor / air filtration system / air purifier

SPL400-3D 3D Printer Fume Extractor

SPL400-3D connected to two (2) 3D Printers

You can even hook up one of the SPL400 series to two (2) of your 3D printers – neat eh?

Features

  • Ideal for 3D Printing , AM applications generating low debris
  • Medium pressure motorized brushless impeller
  • Enhanced mobility with heavy duty lockable casters
  • Multi-stage filtration system: pre-filter, HEPA and chemical filter
  • Whisper quiet operation
  • Optional digital control panel

Specifications

  • Air Flow: 510 m³/h / 300 CFM
  • Motor(s): Motorized impellers, backward inclined, non-overloading
  • Voltage: 120V or 230V
  • Dimensions: 13″W x 16″D x 20″H / 330mm x 406mm x 508mm
  • Filter Sequence: 4″ high capacity pleated pre-filter, 30% ASHRAE (F164), 6” Medical grade HEPA Filter 99.97% (F075), 2“ Chemical filter (F072-GPC)

    More chemical filtration: 4″ high capacity pleated pre-filter, 30% ASHRAE (F164), 2” Medical grade HEPA Filter 99.97% (F074), 6“ Chemical filter (AG-GPC)

  • Optional lnlets: 3” or 4″ diameter
  • Discharge: Recirculation grille
  • Sound Level: 54 dBA at full speed
  • Remote Control: Optional
  • Suction hose: 6 feet (2m) of heavy duty hose & clamps

Kindly contact us for more information or for help with placing your order, toll free, 1-800-626-0664 or through the contact form on this page. We will get back to you as soon as possible.

 

Fume Extractors for 3D Printing, Additive Manufacturing Technologies, AMT

Looking for fume extractor and / or an air filtration system solution to your 3D printing, AM application? We’ll be happy to assist you. Call us toll free, 1-800-626-0664 from anywhere in North America or +1-514-364-5538 outside of the Continental US and Canada.

You can also use the contact from below – we will get back to you as soon as possible.
Screen Shot 2017-08-14 at 1.47.09 PM

Learn more about 3D Printing aka AM (Additive Manufacturing):

3D printing, also known as additive manufacturing (AM), refers to processes used to create a three-dimensional object[1]in which layers of material are formed under computer control to create an object.[2] Objects can be of almost any shape or geometry and are produced using digital model data from a 3D model or another electronic data source such as an Additive Manufacturing File (AMF) file. STL is one of the most common file types that 3D printers can read. Thus, unlike material removed from a stock in the conventional machining process, 3D printing or AM builds a three-dimensional object from computer-aided design (CAD) model or AMF file by successively adding material layer by layer.[3]