Up to 8 soldering stations can be filtered using a single QUATRO SPH-426 high pressure filter system

Up to 8 soldering stations can be filtered using a single Quatro SPH-426 high pressure filter system.

Systems comes complete with patent pending Laser Blue Gel Seal ensuring zero by-pass for any toxic fumes.

Each system comes complete with initial set of filters including a 30% ASHRAE rated pre-filter, 99.97% certified medical grade HEPA filter, and an 8 inch deep bed chemical filter.

The microprocessor control panel is complete with visual and audible alarms, digital speed control, the ability to be interlocked for remote on/off, auto flow adjusts speed of blowers as filters get dirty.

Available accessories include snap together ducting / piping, industrial heavy duty hose, and table mounted extraction arms with damper control and various nozzle attachments.

Call for help with your product selection and / or for assistance with placing your order: 1-800-626-0664.

You may also send us a filled out contact form – http://www.airpurifiers-r-us.com/contact.html

Thanks and have a wonderful day!!😊👌👍

Advertisements

SPH800 Multi-Station SOLDER FUME EXTRACTOR FOR HIGH VOLUME APPLICATIONS

SPH800 with 10 Soldering Stations

SPH800 with 10 Soldering Stations

  • Cost-effective high pressure system
  • LaserBlue gel seal guarantees ZERO FILTER BYPASS
  • Whisper quiet operation
  • Enhanced mobility with heavy duty lockable casters
  • Powered by 3 high-speed turbines (CSA/UL approved)
  • Digital control panel
  • Up to 100 lbs. (45 kg) of chemical filtration media
  • Also available: brushless units and custom filter configuration

Contact us toll free from anywhere in North America, 1-800-626-0664, or send us a completed contact form at – https://cleanairsolution.wordpress.com/contact-us/

Quatro Air Technologies MULTI-USER SOLDER FUME EXTRACTOR Model # SPM504

Multi-station soldering fume extractor configuration with optional capture arms

Multi-station, multi-user, soldering fume extractor system – up to four (4) users

  • Ideal for up to 4 workstations
  • Medium pressure motorized brushless impeller
  • Enhanced mobility with heavy duty lockable casters
  • Multi-stage filtration system: pre-filter, HEPA and chemical filter
  • Whisper quiet operation
  • Optional digital control panel

Multi-station configuration with optional capture arms: AA006 (unit mount) and AA062 (table mount) – see above photo.

Call us for more information, toll free anywhere in North America, 1-800-626-0664 or go to our contact page and send us the completed Contact Form.

Happy Soldering!! 👍😊

Replacement filters for your Quatro Air Technologies fume extractor, air filtration system

3dprinting_sph400_filtersLooking for replacement / spare filters for your Quatro Air Technologies product (fume extractor, dust collector, AF series / BP series air filtration systems, air purifiers, air cleaners, air scrubbers? Look no further. We can help you.

Tell us what you need.

Looking for a fume extractor, dust collector, air purifier for home, office, medical, commercial, industrial application? Looking for an air filtration system to remove dust particulate, chemical gas, odor, fumes in your shop, lab, clinic, print room, etc??

Come and visit our website at http://www.airpurifiers-r-us.com/index.html

SPH400, SPH426, Not Your Ordinary Laser Fume Extractor, Air Filtration System

Our most popular model Laser Fume Extractor for light and medium duty applications

The SPH400 series Laser Fume Extractor, Air Filtration System, is our most popular model for light and medium duty applications. It’s made here in North America, in Pointe-Claire, Quebec, Canada but has found its way to shops, labs, offices, workplaces around the world.

Here’s why.

4 stages, multi-stages of filtration

Capture-PF400-PF800

The Quatro Air SPH400 Fume Extractor and Air Filtration System is designed with up to 4 stages of filtration each targeted for removal of specific size particles and gases.

There are a series of filters in the system to ensure that all particulate matter/ dust is removed efficiently:

The unit contains multi-layer knock out pad filters, Deep Pleated high capacity safety filters and a MERV 17 99.97 % HEPA filter.

The HEPA filter is the last particulate filter in the sequence and it is designed to remove 99.97% of all particulate matter that is 0.3 microns and larger.

Same type of filter that is used in hospital operating rooms

This is the same type of filter that is used in hospital operating rooms. Please note as the filters begin to get dirty they also become more efficient making the system more efficient as time goes on. This occurs as it gets more and more difficult for the dust to pass through the filter due to the passages becoming smaller as they become filled with debris.

Odors, Fumes – gas phase filter is quite large and 8” deep

The gas phase filter is quite large and 8” deep in direction of airflow. We have 26 different types of chemical media that can be incorporated into the chemical filter to address and deal with specific contaminants if required.

Depending on the type of media the modules could weigh as much as 40 lbs.

Our standard and most typical module contains a virgin bituminous coal extruded 3-4 mm carbon pellet.

Ideal at removing many VOC’s

This carbon is ideal at removing many VOC’s and has a holding capacity as high as 25 % by weight. Initially the removal efficiency will be 100% for most VOC’s. Over time the mass transfer zone will travel through the chemical filter as it gets consumed.

A gel seal material to guarantee zero by-pass

The chemical filter is seated inside a gel seal material to guarantee zero by-pass of the chemical filter. This is the same material that is used in Pharmaceutical and Hospital environment clean rooms. All gases therefore must pass through the chemical filter

High pressure blowers to overcome the resistance created by the deep bed chemical filter

Unlike other systems that have a sprinkling of carbon our gas phase chemical filter is quite large and requires the use of high pressure blowers to overcome the resistance created by the deep bed chemical filter. Our blowers are capable of generating 90” water column of pressure. With this type of blower as the filters begin to get dirty and plugged we can still effectively overcome this increase in pressure. The system is equipped to advise you when the filters need to be changed.

For more information, visit our webpage at : http://www.airpurifiers-r-us.com/laser-fume-extractor.html or contact us using the contact form below.

Light Duty 3D Printing Fume Extractor

Looking for a light duty 3D printing fume extractor, air filtration system?

Screen Shot 2017-07-26 at 2.41.38 PMLook no further, we have one for you.

Meet our Quatro SPL400 series dust / fume extractor / air filtration system.

Available with various useful optional pieces such as unit mounted capture arm with plexi nozzle, foot switch for remote on/off capabilities, choice of two filter sequence, for airborne particulate concern as well as mainly VOCs, chemical odor removal.

  • Ideal for 3D Printing , AM applications generating low debris
  • Medium pressure motorized brushless impeller
  • Enhanced mobility with heavy duty lockable casters
  • Multi-stage filtration system: pre-filter, HEPA and chemical filter
  • Whisper quiet operation
  • Optional digital control panel

Call us for help with your product selection, toll free: 1-800-626-0664, from anywhere in North America or fill out and send us the contact form below.

Happy 3D Printing everyone! 🙂

 

Extract fumes from injection molding machines

R.H. wrote to inquire about our fume extractors for use when purging their injection molding machine – issue with smoke and odor:

We would only open the exhaust when purging the machine, so I only envision one machine needing extraction at a time.  We never run more than four machines total, so worst case scenario, we’d need to extract from four.  I envision having flexible ducting to each machine, with a open/closeable vent at each machine above the nozzle.  If that isn’t feasible, I would see if there is a way we could fabricate an enclosure around the nozzle.  As far as the manifold goes, I envision something very much like the one pictured in your brochure with the ten stations (an 8-10 ft. section of pvc with ports coming off of it), the only difference, is the flexible hose (duct hose) would be longer than what is pictured.

After going back and forth discussing various options, we have decided to go with the CSA626 Fume Extractor with a modified filter sequence incorporating a 20″ chemical filter section.

R.H writes back, after the unit was delivered and put to use:

I just put the fume extractor to use for the first time; on a machine/material that has known to “smoke out” the building…let me say, I am thoroughly impressed with the performance of the unit.  I have to admit, I was somewhat skeptical when you stated that it would remove the smell as well, but sure enough, it’s performing just like you said it would.  It looks as though  all of the research/questions have resulted in receiving a great product…thanks!

Best Regards,

R

CSA-600 - Heavy Duty Dust & Odor Removal

The CSA is the workhorse fume extractor of the laser industry; designed to operate in a heavy duty environment. A large pre-filter bag that is easily accessed to change via a convenient side panel eliminates much of the debris that might otherwise clog the more expensive HEPA filters. A huge chemical bed of 66Lb. (30kg) provides significant odor and VOC protection for much longer than the light duty units again providing a solution that can withstand a heavy workload. Chemical compounds can be customized based on specific applications With large collection bag, HEPA Filter & Deepbed Odor filters LaserBlue Gel seal guarantees NO BYPASS Dual hi-speed turbine for high suction, pressure & airflow Whisper quiet operation is office friendly Universal design allows for 2.5″, 3″, 4″ inlet along with discharge

Call us toll free, 1-800-626-0664, for help with your product selection, or use the contact form below.