Fume Extractor, Light Duty, Multi-station, multi-user configuration with optional capture arms

Ideal for up to 4 workstations, Medium pressure motorized brushless impeller, Enhanced mobility with heavy duty lockable casters, Multi-stage filtration system: pre-filter, HEPA and chemical filter, Whisper quiet operation,  Optional digital control panel

  • Air Flow: 1100 m³/h / 475 CFM
  • Motor/fan: Backward inclined, non-overloading, brushless
  • Voltage: 120V or 230V
  • Dimensions: 15″W x 23″D x 30″H / 381mm x 585mm x 762mm
  • Filter Sequence: Pleated pre-filter, 30% ASHRAE (F265), Medical grade HEPA Filter 99.97% (F057), Chemical filter (F033-GPC)
  • Optional lnlets: 2×3”, 3×3” or 4×3″
  • Discharge: Recirculation grille; optional silencer (H250]
  • Sound Level: 62 dBA at full speed
  • Remote Control: Optional
  • Suction hose: 6 feet (2m) of heavy duty hose & clamps
soldering-spm504

Ideal for up to 4 workstations, Medium pressure motorized brushless impeller

Kindly contact us for help with your product selection, pricing, and / or help with ordering, Toll free: 1-800-626-0664.

You may also use the contact form on this page. Have a wonderful day!! 🙂

Advertisements

SolderPure with dual work-station configuration

Did you know you can get a SolderPure solder fume extractor configured for a dual work-station set up?

Yes – it is like get two (2) for the price of one unit. Neat eh?! 🙂 But seriously, one of the neat features of the SolderPure is that it could cover two soldering stations with one single SolderPure solder fume extractor / air filtration system.

Screen Shot 2017-07-26 at 2.41.38 PM

Features that make this a worthwhile investment:

  • Ideal for low debris generating applications
  • Motorized brushless impeller
  • Enhanced mobility with heavy duty lockable casters
  • Multi-stage filtration system: pre-filter, HEPA and chemical odor filter.
  • Whisper quiet operation
  • Digital control panel

Call us toll free, 1-800-626-0664, for help with your product selection or fill out and send us the contact form on this page.

Happy soldering!!

Multi-Station Soldering Fume Extractor Air Filtration System

 Multi-station solder fume extractor and air filtration system
  • Heavy gauge welded Steel Construction
  • Powder coated standard Quatro white
  • Standard inlet dual 3” (75 mm) diameter hose collars, optional
  • 1.5”(38mm), 2”(50mm), 2.5”(127 mm), 4”(100mm)
  • (10) table mounted arms part # AA116 complete with tapered nozzles, table brackets and individual blast gates for air balancing
  • Main manifold piping by others
  • Discharge grills located underneath system
  • Maximum Airflow 534 CFM
  • Maximum static pressure capability 44” WC.
  • Whisper quiet operation
  • (2) CSA / UL approved 1100 Watt brushless type blowers(Brushed type motor / blower also available)
  • Model SPH-82B5, 230 volt ONLY single phase, 12 amps
  • Blowers are complete with thermal cut-outs
  • 6’ (2 meter) electrical cord set
  • Digital Control Panel:
    Manual on/off switch
    subD 9 pin interface for auto On/Off
    Resettable circuit breaker protection
    Speed control
    Auto-flow (automatically speeds up as filters get dirty)
    Pressure sensor monitoring filter status
    Audible alarms for filter and motor status
    Visual lights for operation, filter and motor status
  • Easy tool less filter change out
  • 3’ (1 meter)of heavy duty industrial hose per capture arm
  • Limited one year warranty
  • Dimensions: 16” x 25” x 30” High (406mm x 635mm x 760mm High)
  • Approximate operating weight is 150 lbs (68 kg)
Contact us for help with your product selection, toll free at 1-800-626-0664 or fill out the contact form on this page.
Thank you and Happy Soldering!! 🙂

Premature clogging of main filters – HEPA filter and the Odor Filter / Chemical Filter

Laser cutting with wood produces “sticky smoke”

The CSA600 series Fume Extractor and Air Filtration System is designed with up to 4 stages of filtration each targeted for removal of specific size particles and gases.

There are a series of filters in the system to ensure that all particulate matter/ dust is removed efficiently:
• The unit contains Merv 13 Bag filters, Deep Pleated high capacity safety filters and a MERV 17 99.97 % HEPA filter.

CSA-600 - Heavy Duty Dust & Odor Removal

The CSA is the workhorse fume extractor of the laser industry; designed to operate in a heavy duty environment. A large pre-filter bag that is easily accessed to change via a convenient side panel eliminates much of the debris that might otherwise clog the more expensive HEPA filters. A huge chemical bed of 66Lb. (30kg) provides significant odor and VOC protection for much longer than the light duty units again providing a solution that can withstand a heavy workload. Chemical compounds can be customized based on specific applications With large collection bag, HEPA Filter & Deepbed Odor filters LaserBlue Gel seal guarantees NO BYPASS Dual hi-speed turbine for high suction, pressure & airflow Whisper quiet operation is office friendly Universal design allows for 2.5″, 3″, 4″ inlet along with discharge

• The HEPA filter is the last particulate filter in the sequence and it is designed to remove 99.97% of all particulate matter that is 0.3 microns and larger.
• This is the same type of filter that is used in hospital operating rooms. Please note as the filters begin to get dirty they also become more efficient making the system more efficient as time goes on. This occurs as it gets more and more difficult for the dust to pass through the filter due to the passages becoming smaller as they become filled with debris.
The gas phase filter is quite large and 15” deep in direction of airflow. We have 26 different types of chemical media that can be incorporated into the chemical filter to address and deal with specific contaminants if required.
• Depending on the type of media the modules could weigh as much as 70 lbs.
• Our standard and most typical module contains a virgin bituminous coal extruded 3-4 mm carbon pellet.
• This carbon is ideal at removing many VOC’s and has a holding capacity as high as 25 % by weight. Initially the removal efficiency will be 100% for most VOC’s. Over time the mass transfer zone will travel through the chemical filter as it gets consumed.
• The chemical filter is seated inside a gel seal material to guarantee zero by-pass of the chemical filter. This is the same material that is used in Pharmaceutical and Hospital environment clean rooms. All gases therefore must pass through the chemical filter
Unlike other systems that have a sprinkling of carbon our gas phase chemical filter is quite large and requires the use of high pressure blowers to overcome the resistance created by the deep bed chemical filter. Our blowers are capable of generating 90” water column of pressure. With this type of blower as the filters begin to get dirty and plugged we can still effectively overcome this increase in pressure allowing us to continue to evacuate the laser chamber. The system is equipped to advise you when the filters need to be changed.

Contact us for help with your Laser Cutting, Engraving Fume Extraction System needs:

Call us toll free in North America 1-800-626-0664 or fill out the contact form below.

Thanks and have a great day!!

Laser Fume Extractor For Small Operation | Hobbyists | Metal Marking

Laser Fume Extractor For Small Operation | Hobbyists | Metal Marking

Ideal for low debris generating applications like metal marking
Medium pressure motorized brushless impeller motor blower, 300 CFM, 120V or 230V
Enhanced mobility with heavy duty lockable casters (wheels)
Multi-stage filtration system: pre-filter, HEPA and chemical filter
Whisper quiet operation, 54 dBA at full speed
Optional digital control panel

Laser Fume Extractor – SPL400 – ideal for small operations like Metal Marking

Contact us for help with your product selection – toll free North America – 1-800-626-0664

BP2000 Laser Fumes Extractor For Heavy Duty Applications

BP2000 Laser Fumes Extractor For Heavy Duty Applications

BP2000 Laser Fumes Extractor – Air Filtration System

Filters:
2 x 2″ Pleated Pre-Filter (F001)
12″ HEPA Filter (F002)
12″ Activated Carbon filter (F003-GPC)

Contact us for help with product selection – toll free : 1-800-626-0664 or fill in the contact form below:

Laser Cutting | Safety concerns when cutting MDF | Laser Fumes Smoke Extractor

Safety concerns when cutting MDF

When MDF is cut, a large quantity of dust particles are released into the air. It is important that a respirator is worn and that the material is cut in a controlled and ventilated environment. It is a good practice to seal the exposed edges to limit the emissions from the binders contained in this material.

Formaldehyde resins are commonly used to bind together the fibres in MDF, and testing has consistently revealed that MDF products emit free formaldehyde and other volatile organic compounds that pose health risks at concentrations considered unsafe, for at least several months after manufacture.[7][8][9]

[ More of the above article – https://en.wikipedia.org/wiki/Medium-density_fibreboard ]

Be forewarned – cutting MDF and similar wood products consume particulate filters quickly

Unfortunately certain woods such as MDF (containing glues, adhesives , resin) will consume filters quickly.

If you work with these materials lots we suggest getting the PF400 – http://www.airpurifiers-r-us.com/pf400-laser-fume-extractor-prefilter-section.html – the pre-filter bag section is incorporated into the CSA600 series.

PF400S Pre-Filter Section

  • Multiple high density layered antimicrobial filter bags x 2
  • Easy to change
  • Large holding capacity
  • Self contained pre-filter section can be combined with any existing system that requires additional particulate filtration
  • Can also snap onto existing SPH400 system

Resins in wood

The resin could be in the wood itself or if many layers are bonded together the bonding adhesives / glues could be the culprit. Essentially the laser vaporizes the adhesive or resinous material which then condenses / sticks and clogs the filters rapidly.

Sometimes it is the natural resins within a particular wood.

When this type of material is lasered the fumes can sometimes block the pores of the filters. This will not be unique to Quatro’s filters but to any unit that contains particulate / HEPA filters.

Installing a pre-filter section may prolong the life of the HEPA filters. It all depends on what type of debris is being generated in the particular application.

For those unfortunate to have an application where HEPA filters are being blinded quickly we have two items we can offer:
1) The PF400A pre-filter section $653.00
2) Part # AG189 (box of 6 HEPA’s for the price of 3) ……… $351.00 USD
(Prices subject to change without prior notice)

Call us for help with your Laser Fume Extractor / Air Filtration System.

Contact Us
Toll Free: 1-888-395-0330 or 1-800-626-0664 (North America- Continental USA and Canada)
Skype: lito.espinosa
Outside of North America: 1 (514) 421-0658

Fill out the Contact Form: